National Music Museum Logo   National Music Museum  
Home  Collections
Virtual Tour
Calendar Gift Shop FAQ Site Index Maker Index

 

NMM 13439.  Guitar by Gibson, Inc., Kalamazoo, 1939.
Recording King Jumbo Guitar (551 C 1027) model (16″).  Serial number EW-1683.
John R. Barmeyer Collection, 2007.

Note: Click on any image below to see a larger image.


NMM 13439.  Guitar by Gibson, Inc., Kalamazoo, 1939. Bass side Treble side Back

The Recording King brand was applied to the stencil-line guitars made by several American manufacturers to be sold by Montgomery Ward. In their 1939 catalog, Wards promoted these instruments by appealing to thrifty customers looking for quality at a cut rate: "Same quality sold by music stores . . . at Wards you save $2 to $66. Hereís the reason why:  three of the best known makers of fretted instruments in the country made the models on these pages. Theyíre made of the same costly materials as those guitars which bear the makersí own names. When you buy them by the mail at Wards, you pay no costly selling expenses or salesmenís commissions. You buy direct! Remember, these are Brand New Instruments—not to be confused with reconditioned or studio-used models frequently sold at these low prices."

The Recording King Jumbo guitars, endorsed by Ray Whitley and available with rosewood or mahogany backs, represented an extraordinary value for a high-quality Gibson. The rosewood model shared the proportions and batwing-style bridge of Gibsonís own J-55, and sold for a mere $29.95 (with "usually $80" noted nearby in the catalog) compared to the $55 Gibson-brand Jumbo, which had a lower-grade mahogany back. The mahogany-backed Recording King cost even less—only $19.95 ("usually $37.50," according to Wards catalog, the price of Gibsonís J-35).

To clinch this phenomenal deal, Wards' final selling point boasted that "Recording King Jumbo Guitars have the full endorsement of Ray Whitley, Hollywood screen guitarist. Each has a flat top and back with a wider, deeper body, which means deep tones; just right for accompaniments. The following points are found on both Jumbos: celluloid bound rosewood finger board with inlaid pearl markers; rosewood bridge; vertical type peghead; hooks on end of body for cord."


Inscriptions:
Cursive stenciled lettering in black paint on head mother-of-pearl inlay:
Recording / King
Cursive stenciled lettering in white paint on head: Ray Whitley
Stamped on back of head, underneath lacquer: EW-1683

Inscription

Front and Back Views of Body


Front of body Back of body

Body: Soundboard:  two-piece spruce:  narrow grain broadening toward the flanks. Back:  two-piece rosewood; no back stripe. Ribs:  two-piece rosewood; no end graft. Head:  dark-brown, lacquered maple veneered with black-lacquered maple; Recording King stenciled in black paint on rectangular mother-of-pearl inlay; mother-of-pearl crown with black-painted details above Recording King signature; no truss-rod cover. Neck:  dark-brown, lacquered maple; integral with head; rosewood-maple-rosewood stripe on back of neck, the center strip wider.


Fretboard, Front and Back of Peghead, Bridge

Fretboard Front of peghead Back of peghead Back of neck

Inlay on fretboard

Bridge

Trim: Heel cap:  none; neck heel recessed from back. Fingerboard:  rosewood bound in white celluloid; 19 nickel-silver frets; 5 mother-of-pearl diamonds behind 3rd fret, 4 mother-of-pearl diamonds behind 5th fret, 3 mother-of-pearl diamonds behind 7th, 9th, 12th, and 15th frets; single, imitation tortoise-shell, celluloid side dots behind 3rd, 5th, 7th, 9th, 12th, and 15th frets. Nut:  bone; later. Bridge:  rosewood with festooned lower edge, known as "batwing"; three mother-of-pearl dots inlaid below bridge pins; angled bone saddle; white plastic bridge pins. Tuners:  six chrome-plated, steel, Grover worm-gear machine tuners with decoratively cut, plate outlines with pressed groove border; chrome-plated steel heads. Endpin:  white plastic; extends through nickel-plated steel strap holder secured to rib with three nickel-plated steel Philips head screws; corresponding nickel-plated steel strap loop secured to back of head with two nickel-plated steel Philips head screws. Pick guard:  imitation tortoise-shell celluloid; engraved border and decorative, engraved, abstract foliate design; edges tapered outside border; overlaps soundhole trim and binding.


Neck Heel, Soundhole, and Pick Guard

Neck Heel

Soundhole Pick Guard

Inlay: white celluloid; two-ply, white-and-black, celluloid-strip trim on top; no additional trim. Rosette:  soundhole bound in white celluloid with two-ply (black-white) celluloid purfling strips. Back stripe:  none. End graft:  none.

Interior: Linings:  kerfed maple. Neck block:  mahogany; beveled edges. End block:  mahogany; beveled edges. Top braces:  spruce X-brace, the joint of main cross brace reinforced with white cloth; transverse and finger braces with tapered ends; maple bridge plate. Back braces:  spruce back graft; four spruce back braces with tapered ends. Rib grafts:  12 spruce grafts with tapered ends on inside of ribs.


Bottom Rib

Bottom Rib



Measurements: Total guitar length:  1039 mm (40-29/32″)
Back length:  516 mm (20-5/16″)
Upper bout width:  292 mm (11-1/2″)
Waist width:  267 mm (10-1/2″)
Lower bout width:  408 mm (16-1/16″)
Rib height (including edging) at heel:  98 mm (3-27/32″)
Rib height, at waist:  106 mm (4-5/32″)
Rib height, at end block:  123 mm (4-27/32″)
Head length:  173 mm (6-13/32″)
Head width, top:  88 mm (3-7/16″)
Head width, bottom:  79 mm (3-3/32″)
Neck length (nut to ribs):  351 mm (13-13/16″)
Neck width, nut:  44 mm (1-3/4″)
Neck width, heel:  57 mm (2-1/4″)
Soundhole diameter:  103 mm (4-1/16″)
Vibrating string length (nut to bridge edge):  high E:  631 mm (24-7/8″); low E:  635 mm (25″)

Return to Gibson Acoustic Guitar Checklist

National Music Museum
The University of South Dakota
414 East Clark Street
Vermillion, SD 57069

National Music Museum, 2007-2014
Most recent update: March 24, 2014

The University of South Dakota
Return to Top of Page